6ES7153-2BA10-0XB0 | SIEMENS

Siemens 6ES7 153-2BA10-0XB0 SIMATIC S7 DP IM 153-2 High Feature Interface Module for ET 200M

Distributed I/O System, supports up to 12 S7-300 Modules, 1 x 12Mbps RS-485 PROFIBUS DP Interface

(Slave), supports Remove/Insertion Under Power, Redundancy and Time Stamping, fits for Isochronous

Mode with new features: 12 Modules/Station slaves; initiative for switches & drives; extended data for HART

secondary variables operation with 64-Point modules; extends timestamps with 32 signals/slot; IP20 Protection,

24V DC Power

Data sheet 6ES7153-2BA10-0XB0
SIMATIC DP, Connection ET 200M IM 153-2 High Feature for max.
12 S7-300 modules with redundancy capability, Timestamping
suitable for isochronous mode New features: up to 12 modules can
be used Slave INITIATIVE for Drive ES and Switch ES Expanded
quantity structure for HART auxiliary variables Operation of the 64-
channel modules 32 signals/slot +++Observe compatibility notes in
manual+++
General information
Product type designation IM 153-2 DP HF
Firmware version V6.0.0
Vendor identification (VendorID) 801Eh
Supply voltage
Rated value (DC) 24 V
● 24 V DC Yes
permissible range, lower limit (DC) 20.4 V
permissible range, upper limit (DC) 28.8 V
external protection for power supply lines
(recommendation)
2,5 A
Mains buffering
● Mains/voltage failure stored energy time 5 ms
Input current
Current consumption, max. 650 mA; with 24 V DC supply
Inrush current, typ. 3 A
I²t 0.1 A²·s
Output current
6ES7153-2BA10-0XB0 Subject to change without notice
Page 1/
3
11/13/2019 © Copyright Siemens
for backplane bus (5 V DC), max. 1.5 A
Power loss
Power loss, typ. 5.5 W
Address area
Addressing volume
● Inputs 244 byte
● Outputs 244 byte
Hardware configuration
Number of modules per DP slave interface, max. 12
Time stamping
Accuracy 1 ms; 1ms at up to 8 modules; 10ms at up to 12 modules
Number of message buffers 15
Messages per message buffer 20
Number of stampable digital inputs, max. 128; Max. 128 signals/station; max. 32 signals/slot
Time format RFC 1119
Time resolution 0.466 ns
Time interval for transmitting the message buffer if a
message is present
1 000 ms
Time stamp on signal change rising / falling edge as signal entering or exiting
Interfaces
Transmission procedure RS 485
PROFIBUS DP
● Node addresses 1 to 125 permitted
● automatic detection of transmission rate Yes
● Output current, max. 70 mA
● Transmission rate, max. 12 Mbit/s
● SYNC capability Yes
● FREEZE capability Yes
● Direct data exchange (slave-to-slave
communication)
Yes; as publisher with all IO, as subscriber with F-IO only
● Design of electrical connection of PROFIBUS
interface
9-pin sub D
1. Interface
PROFIBUS DP slave
● GSD file SI05801E.GSG
● automatic baud rate search Yes
Protocols
Bus protocol/transmission protocol PROFIBUS DP to EN 50170
Protocols (Ethernet)
● TCP/IP No
6ES7153-2BA10-0XB0 Subject to change without notice
Page 2/
3
11/13/2019 © Copyright Siemens
Potential separation
Potential separation exists Yes
Isolation
Isolation tested with Isolation voltage 500 V
Degree and class of protection
IP degree of protection IP20
Ambient conditions
Ambient temperature during operation
● min. 0 °C
● max. 60 °C
● horizontal installation, min. 0 °C
● horizontal installation, max. 60 °C
● vertical installation, min. 0 °C
● vertical installation, max. 40 °C
Altitude during operation relating to sea level
● Installation altitude above sea level, max. 3 000 m
Configuration
Configuration software
● STEP 7 Yes; STEP 7 / COM PROFIBUS / non-Siemens tools via GSD file
Dimensions
Width 40 mm
Height 125 mm
Depth 117 mm